GUSEN brings you to know the relevant information of self-cutting anchor , which can reduce the noise during welding. Due to the large mutual adhesion between the bolt and the steel plate, so during welding, no noise will be generated. And because the welding time is relatively short, so it will not affect the whole machine. In addition, wire breakage can be avoided in the welding process. In this way, the efficiency of the incision is greatly improved. When there is no mutual connection between the self-cutting bottom anchor bolt and the steel plate, no manual operation is needed because there is no mutual connection between the nut and the steel plate. The welding process of the self-cutting bottom anchor is quieter and faster without manual operation. In the welding process of self-cutting bottom anchor bolt, manual operation is not needed when the nut and the steel plate are not connected with each other or when the nut and the steel plate are not connected with each other.
Self-cutting anchor bolt manufacturers, the function of automatic cutting bolts is to ensure that no one operates in the installation project. The self-cutting bolt can be in a fixed position so that the anchor cannot be tightened. When tightened to the mounting torque, it ensures that there is no loosening between the bolt and the nut. The function of the automatic cutting bolt is to ensure that there is no loose between the bolt and the nut. The main advantages of the machine include the use of a better nut connecting rod type tightening technology. During the installation process, the welding time is short due to the large tightening force of the anchor chain nut. In the process of installation, due to the greater tightening force of anchor chain bolts, so that the weld length and other advantages. In the process of installation, due to the large tightening force of anchor chain bolts and weld length and other advantages. We used a special design process to achieve this.
Self-expanding bottom mechanical anchor how much money, after the installation of the nut in normal use, can be tightened at will, will not cause fracture because of the different composition of the anchor nut. After the installation of the nut in the process of use, can automatically overhaul, adjust the bolt and grounding line. If it is necessary to replace the screws or replace the ground line, it can also be done through the built-in power supply of the machine. At the cut, a special technique is also used to prevent the bolt from falling off. The technology, developed and marketed by Sanyo, prevents bolts from falling off during installation. The advantage is that different sizes of steel plates can be used. The steel plates are separated from each other. The contact between the steel plate and other parts makes the welding stronger.
Self-cutting mechanical anchor wholesale, when the wire rope and wire rope fracture, automatic bottom cutting bolt can be pulled away. When a fracture occurs between the position of the self-cutting bottom bolt and the cone position, the self-cutting bottom bolt can be pulled apart. The method of automatic adjustment of cone position and cone position is realized by adjusting the height and width between the wire rope and wire rope. The machine has automatic adjustment function, can be adjusted at any time according to user needs. In addition, the machine also adopts automatic control system and electronic control system. These designs allow the nuts and bolts mounted on the body to work together. The bolts installed in the middle of the car body, the lower part of the door and the inside of the trunk can not only ensure protection, but also play a protective role.
Self-cutting mechanical anchor manufacturers, which is conducive to reducing the friction between the bolts. At the same time, the friction between the screw and the wire can be reduced. Tension should also be applied to the joints of bolts. If the friction between the nut and the wire at the joint is too high, a tension force should be used. This can reduce the friction between the bolt and the wire. In the installation, we should pay attention to the following aspects of the nut can not have wear. Because it does not require a reaming bit. In use, the bolts can also be fixed to a large cylindrical steel plate. In this way, the defects of the tightening bolts are avoided. In addition, in order to prevent the nut loosening, falling off and other problems, it also designed a small tightening bolt. Due to the special bolt structure and design concept.
Adopt high pressure welding technology. This technique can not only make the anchor body and the bit form a good symmetrical structure and stability when welding on the bolt. Three is the use of high temperature heat sealing technology. This technology makes the friction between the bolt and the bit smaller, which can prevent the friction between the anchor and the bit. It is reported that this high pressure welding technology is installed and welded by high temperature heat sealing technology in China, which has great economic benefits. The product is characterized by a good tightening mechanism, which can fix the bolt nut on the bolt without destroying the composition of the bolt nut when the bolt nut has a self-cutting mechanical locking effect. The design can improve the balance between anchor column and ground clearance and ground clearance. The steel plate structure is tightened, which makes the steel plate structure have good contact with the ground.
Post time: Aug-18-2022